oil hole
英 [ɔɪl həʊl]
美 [ɔɪl hoʊl]
n. 注油孔
双语例句
- When the oil filter works, oil ejected from the oil injection hole makes the rotor rotate and flushed the impurity on a filter screen.
当滤油器工作时，从喷油孔喷出的油一方面使转子转动，一方面冲洗滤网上的杂质异物。 - The fixture used for oil hole drilling has both ID and OD location by improving the structure of the fixture, so as to expand application scope and reduce production cost.
通过对轴承钻油孔夹具结构的改进，使钻油孔夹具内径与外径定位兼备，扩大使用范围，降低制造成本。 - Some connecting rods have an oil spurt hole in the yoke or at the cap-mating surface to provide cylinder wall lubrication.
有些连杆轭部或相配连杆盖表面上有油喷口，其目的是为气缸壁起到滑作用。 - The oil injection hole is a concave channel shape or planar oil injection hole which is arranged on the side surface of the motor shaft.
注油孔为设在电机轴侧面的凹槽形或平面形注油孔。 - Calculation and Application of Process Parameter for Machining Oblique Oil Hole of Crankshaft;
在分析孔斜原因的基础上，介绍了该工程的防斜、纠斜技术措施和取得的效果。 - Host shaft had stretched place design of the oil hole back to the shaft sealing, prevent the leakage of oil;
主机轴伸处设计了带回油孔的轴封，防止了润滑油的渗漏； - A plurality of sealing cavities are arranged in the supporting device, and the semi-solid sealing medium is poured in the sealing cavities through the oil feeding hole.
支承装置内开有数个密封腔，通过注油口向密封腔内注有半固态密封介质； - Self-aligning bearing outside diameter design have oil, lubricating oil hole effect is good.
调心轴承外径设计有油槽油孔，润滑效果好。 - Oil spewed from the hole.
油从洞里喷出来。 - An oil jet hole, in the rod journal end ( large end) lubricates the rod small end, piston and cylinder inner surface.
油喷孔在日志结尾杆（大底），润滑连杆小头，活塞和气缸的内表面。 - The utility model provides a main shaft sealing device for a large-size washing machine, comprising a supporting device, sealing medium, an oil feeding hole, a sealing element, etc.
一种大型洗衣机主轴的密封装置，它是由支承装置、密封介质、注油孔、密封件等组成； - At the same time, the improved method was put forward and the application and optimization of air conditioning gas-liquid separator were expounded, especially the design of the oil return hole.
同时提出了针对性的改进措施，对空调气液分离器的应用及优化设计，尤其是回油孔的设计进行了详细的阐述。 - Alternatively, the oil injection hole is the round or square oil injection hole which is arranged at the positions of the side wall or end surface of the motor shell corresponding to the bearing.
或为设在电机壳体侧壁或端面上对应于轴承部位的圆形或方形注油孔。 - An oil returning hole connected with the other end of the oil returning pipe is arranged on the base.
底座上设置与回油管另一端相连接的回油口； - Research on Processing Technique of Slant Oil-hole through Big-side in the Body of Engine
发动机机体通大侧面斜油孔加工工艺研究 - Research on well depth of oil producing slim hole
小井眼采油工艺技术井深界限研究 - Analyzing for stress concentration of oil drain hole of crankshaft by 3 D boundary element method
用三维边界元法分析曲轴加油孔的应力集中 - Flexible Automatic Line of Crankshaft oil& hole
曲轴油孔的柔性自动加工线 - Burring the Oil Hole Edge of Crankshafts by Polishing
曲轴油孔口边毛刺的光整加工 - This article introduces mainly calculation of a slanting angle of crankshaft clamping with the analysis method in machining crankshaft oblique oil hole.
主要介绍在加工发动机曲轴斜油孔时，用解析法计算曲轴装夹时所倾斜的角度。 - Normalized Technological Calculation for Crankshaft Oblique Oil Hole Machining
曲轴斜油孔加工的规范化工艺计算 - When oil enters the hole of water-wet sandstone driven by pressure difference, oil migrates following a line of less resistance because of the migration force of oil is bigger than that of water.
油在压差驱动下注入亲水砂岩孔隙的过程中，油的运移阻力比水大，因而，油往往沿阻力较低的有限通道运移。 - The cracks in oil hole are caused by less a value after machining.
油孔淬裂的主要原因是油孔加工后的α值偏小； - The revolving direction, internal oil hole position and spline shaft of the domestic pump are modified to meet the installation requirement.
为了满足安装的要求，对国产齿轮泵的旋向、内油孔位置和花键轴等进行了改造。 - Preliminary Investigation of HSE Management in Rushing to Repair Construction for Oil Pipeline Against Oil Stolen by Drilling Hole
输油管线反打孔盗油抢修施工中的HSE管理初探 - There are two kinds of the medium frequency quenching crack for the crankshaft, namely, cracks in both oil hole and neck surface.
曲轴中频淬火裂纹有油孔裂纹和轴颈表面裂纹两种。 - Oil engine injector fitting hole and below side of cylinder head form a angle, this hole system can't be measured directly by measurer when they are processed.
柴油机喷油器安装孔与气缸盖下平面成一个角度，该孔系在加工时不能采用量具直接测量，因此，设计了一种检具，它能比较方便地测量柴油机喷油器安装孔。 - The Application of FANUC CNC on Drilling Machine for the Crankshaft Oil Hole
FANUC数控系统在曲轴油孔钻削机床中的应用 - Reasons of sucker rod string lagging in heavy oil slant hole and solving method
稠油斜直井抽油杆柱滞后原因及解决途径 - The influence of the oil hole on small end of connecting rod has been analyzed with the finite element method on two projects: the small end of connecting rod with an oil hole and the small end of connecting rod with double oil holes.
采用有限元方法对两种不同方案的连杆小头油孔（单油孔方案和双油孔方案）进行了分析。